Shop All

Morel MPS 1.550 Amp Monoblock Class D Mono Subwoofer Amplifier 550w RMS at 2ohms

£499.00
In stock
SKU: 91188MPN: MPS 1.550

The Morel MPS 1.550 is a Class D monoblock subwoofer amplifier delivering 350W RMS at 4 ohms or 550W RMS at 2 ohms, part of Morel's MPS amplifier range.

Compatible with the optional Morel MPS-R1 wired remote level control.

Key specifications

  • Power: 350W RMS x 1 at 4 ohms, 550W RMS x 1 at 2 ohms
  • Class: D
  • S/N ratio: 100dB, THD 0.15%
  • Low-pass filter: 40–220Hz, 12dB/octave
  • Bass boost: 0–12dB at 45Hz
  • Subsonic filter: off, 25 or 35Hz
  • Inputs: pre-amp and speaker-level
  • Recommended wiring: 8 gauge, 50A fuse
  • Dimensions: 9-3/8" W x 2-1/8" H x 6-3/4" D

Sub power

The MPS 1.550 is built to partner Morel's own subwoofers, sending up to 550W RMS of clean, high-fidelity power. If you also need amplification for your front speakers, the Morel MPS 4.400 4-channel amplifier is available separately.

Low-noise design

Class D architecture keeps the signal clean with minimal noise. Balanced differential inputs reject interference, and an onboard microprocessor manages thermal regulation under sustained load. All connections are on one side of the amp for straightforward installation.

Tone controls

Low-pass and subsonic filters, bass boost, and gain controls are recessed under a top panel. Speaker-level inputs support DC offset or signal-sensing turn-on but require speaker wire to RCA adapters (not included). Wiring, fuse, and hardware are not included — 8-gauge power and ground leads with a 50A fuse are recommended.

  • Mono subwoofer amplifier
  • 350W RMS x 1 at 4 ohms (550W RMS x 1 at 2 ohms)
  • Class D amp technology
  • 100dB signal-to-noise ratio, 0.15% THD
  • Variable low-pass filter: 40–220Hz, 12dB/octave
  • Variable bass boost: 0–12dB at 45Hz
  • Switchable subsonic filter: off, 25 or 35Hz
  • Pre-amp and speaker-level inputs
  • Speaker-level inputs: DC offset or signal-sensing turn-on
  • Speaker-level inputs require speaker wire to RCA adapters
  • 8-gauge power and ground wires and a 50A fuse recommended
  • Wiring, fuse, and hardware not included
  • Dimensions: 9-3/8" W (including flange) x 2-1/8" H x 6-3/4" D
Specification
SeriesMPS
Article NumberMPS 1.550
Country of ManufactureChina
More specs
  • RMS Power Output (Watts x Channels)    350 x 1
  • Peak Power Output (Watts x Channels)    N/A
  • Power at 2 Ohms (Watts x Channels)    550 x 1
  • Bridged Power (Watts x Channels)    N/A
  • Minimum Impedance Bridged    N/A
  • Minimum Impedance Unbridged    2
  • Minimum Impedance    2
  • Best Frequency Response    10-220 Hz
  • THD at Rated RMS Power    0.15%
  • Signal to Noise Ratio    100 dB
  • Input Voltage    14v
  • Features
  • Amplifier Class    D
  • Low-Pass Crossover Frequency    40-220 Hz
  • Low-Pass Slope (dB/octave)    12 dB/octave
  • High-Pass Crossover Frequency    N/A
  • High-Pass Slope (dB/octave)    N/A
  • Bass Boost    0-12 dB
  • Bass Boost Frequency    45 Hz
  • Fan Cooled    No
  • Fuse Rating    50
  • Speaker Level Inputs    RCA
  • Preamp Outputs    No
  • Width (inches)    9-3/8
  • Height (inches)    2-1/8
  • Depth (inches)    6-3/4
What's Included
  • Mono subwoofer amplifier
  • Four 5/8" Screws
  • Two M4x4mm Machine screws (top panel replacement screws)
  • 2mm Allen wrench
  • 2.5mm Allen wrench
  • 4mm Allen wrench
  • Owner's manual
Product information

Morel

About the Morel MPS 1.550

From our tech experts at CEN

A multi-channel amplifier, Class D, rated at 550w RMS.

Who it suits

Drivers who have upgraded their speakers and found the head unit cannot drive them properly.

Our tech experts advise

Matching matters more than headline watts, and the gains want setting with a meter rather than by ear. It also needs a fused feed from the battery on the correct cable gauge. Installation is priced per vehicle, so get in touch with your make, model and year and we will confirm what it needs. See car audio installation.

Explore the full Morel range at CEN, with fast UK dispatch and expert advice from our Nottingham team. Shop all Morel

Looking for Installation?

At CEN we take pride in being able to share the quality of our work as well as being able to show what incredible products we have installed week on week.

Get a quote

Frequently Asked Questions

Q: How do I choose the right amplifier for my speakers or subwoofer?

A: Match the amplifier's RMS output per channel to the RMS handling of your speakers or subwoofer at the same impedance. The Specification tab lists the power figures. If in doubt, contact CEN with your setup and we will recommend a match.

Q: What wiring do I need to install this amplifier?

A: You will need an amplifier wiring kit sized to the amplifier's power draw, typically including power and earth cable, a fuse, RCA leads and a remote wire. CEN stocks complete wiring kits, and the amplifier's fuse rating is the guide to the cable gauge required.

Q: What class of amplifier is this and does it matter?

A: Class D amplifiers are compact and efficient, ideal for subwoofers and modern installs. Class AB designs are traditionally favoured for outright sound quality on mid and high frequencies. The class is listed in the Specification tab where provided.

Q: Will an amplifier work with my factory head unit?

A: Yes, in most cases. If your head unit has no RCA outputs you will need a line output converter to feed the amplifier a clean signal. CEN stocks line output converters and can advise the right one for your vehicle.

Q: Can CEN install this amplifier?

A: Yes. CEN offers professional amplifier installation from our Nottingham premises, including secure mounting, wiring and setup. Contact us to book.

Q: Does the Morel MPS 1.550 have a bass remote?

A: The optional Morel MPS-R1 wired remote level control is compatible with the MPS 1.550.

Q: Does the MPS 1.550 accept speaker-level inputs?

A: Yes. It has pre-amp and speaker-level inputs. The speaker-level inputs need speaker wire to RCA adapters and support DC offset or signal sensing turn-on.

Q: What is in the box with the MPS 1.550?

A: The amplifier, four 5/8" screws, two M4x4mm machine screws, 2mm, 2.5mm and 4mm Allen wrenches and the owner's manual. Wiring, fuse and hardware are not included.