Hertz Mille Pro MPK 165P.3 6.5" 16.5cm Car 2 Way Component Speaker 115w RMS Pair

The Hertz Mille Pro MPK 165P.3 is a 6.5" (165 mm) 2-way component speaker system rated at 115W RMS / 230W peak at 3 ohms. It includes the MP 165P.3 mid-bass woofer, MP 25.3 Tetolon dome tweeter and MPCX 2P.3 crossover, and sits within the Hertz Mille Pro range.

For the MP 28.3 tweeter and Hi-Contour crossover, see the top of the range MPK 1650.3; for a 5 inch set, see the MPK 130.3.

Key specifications

• Type: 6.5" (165 mm) 2-way component system
• Power handling: 115W RMS, 230W peak
• Impedance: 3 ohm
• Sensitivity: 93 dB SPL
• Frequency response: 45 Hz – 22.5 kHz
• Woofer: MP 165P.3, 14 mm high copper voice coil, 95 mm magnet
• Tweeter: MP 25.3, 29 mm Tetolon dome, 25 mm voice coil
• Crossover: MPCX 2P.3, 4 kHz, 12 dB/octave on the tweeter
• Tweeter level: 0 / +2.5 dB

Extreme dynamics, unlimited power handling, realistic sound stage

The MPK 165P.3 focuses energy in the mid-low range for a strong listening experience, making it an ideal match alongside a powerful subwoofer. The MP 165P.3 woofer's electroacoustic parameters are tuned for pure, solid mid-bass performance in high-dynamic systems.

MP 25.3 tweeter

• Tetolon fibre soft dome for natural, detailed reproduction of musical nuances.
• "Center Tuning Duct" geometry for lower resonance frequency and reduced harmonic distortion.
• High-density flux Neodymium magnet, optimised for control during high-energy dynamic transients in the mid-high frequency range.
• 25 mm ferrofluid-cooled mobile voice coil.
• Rear chamber filled with selected damping material, sized for lower Fs and a well-damped high-pass frequency roll-off, allowing a low cut-off frequency crossover point.
• Faceplate with FEM (Finite Element Modelling) optimised geometry for high linearity in off-axis installations.
• Wide array of installation accessories for easy OEM integration.

MP 165P.3 woofer

• 3 ohm nominal impedance to exploit full amplifier power.
• 14 mm height pure copper voice coil wound on a Polyamide former for exceptional power handling.
• 95 mm diameter magnet to maximise control over the whole excursion.
• Exponential V-cone® profile pressed-pulp cone with cotton fibres, combining stiffness and low weight for a wide frequency response.
• Cone profile geometrically optimised for linearity and dispersion in the mid frequency range.
• "Boundary Free" rubber surround for improved efficiency and wider mid-bass frequency.
• Low mounting depth, acoustically transparent aluminium alloy basket with diamond cutting and aluminium Hertz logo.
• Full protection metal mesh grill with aluminium Hertz logo and mineral powder coated inner grill included, offering several installation combinations.

MPCX 2P.3 crossover

• Two-position (0 / +2.5 dB) tweeter level switch to fine-tune transducer output.
• 160V bi-metallised polyester film capacitors with ultra-low DF for maximum sound transparency and clean mid/hi-frequencies.
• 1 mm pure copper wire inductors with low series resistance for low dissipation losses on the woofer section where high transient currents are demanded.

The MPCX 2P.3 crossover uses a copper inductor with 1 mm diameter wire to filter the MP 165P.3, which at 3 Ω requires high impulse currents. The MP 25.3 tweeter is crossed over at 12 dB/octave using a 160V bi-metallised polyester film capacitor and air coil inductor. The 0/+2.5 dB tweeter level control allows the system response to be tailored to listener preference and installation position.