Shop All

Mosconi Pico 8 | 12 DSP Amp 8 Channel Amplifier with 12 Channel DSP Up to 480w

£969.99 Out of stock
Out of Stock
SKU: 91236MPN: MOSCONI PICO 8|12 DSP

MOSCONI PICO 8 | 12 DSP

8 Channel Amplifier Class D Technology Up to 480 Watts @ 2 Ohm

MOSCONI PICO 8|12 DSP

PERFECT OEM INTEGRATION

Powerful DSP amplifier optimized for factory radio use. Four analog inputs, flexible routing, 3 x input EQ and delay. With 8 x 50 Watts ideal for active multi-way systems and extensive installations. Ready for the future with two digital inputs (SP-Dif and BT+) and two processed line outs.

SIGNAL CONTROLLED POWER SUPPLY

In contrast to Class G/H, the power supply is only switched on when required (high levels) and regulated depending on the power demand. Benefit: The quiescent current is between 250 mA and 450 mA (depending on the speaker circuitry) -> Especially interesting for electromobility and motorhomes

TRANSDUCERLESS HIGH-SPEED PWM POWER AMPLIFIERS

High-efficiency PWM amplifiers with the fastest carrier frequency in the world today (> 2 MHz), enables HiRes audio transmission and the extremely small size. The modulation is done without DAC directly from the 96 kHz TDM signal of the DSP, thus the noise floor is close to zero and THD+N ~ 0.02 % / 1 W.

Specification
Bluetoothextended digital audio port (BT+)
More specs
  • 2 x analog inputs switchable (high level / low level)
  • 1x digital input SP-Dif optical (8 kHz - 96 kHz sampling rate)
  • 1 x bluetooth port with SP-Dif - TTL (8 kHz - 96 kHz, e.g. for Mos AMAS bluetooth streaming module)
  • (flexible 8 kHz - 384 kHz synchronous digital input for audio sources with 2 - 16 channels, direct DSP access without jitter, e.g. for MOS BTS-LD4C BT streaming module or extended analog inputs)
  • 294.912 MHz, 32-bit audio port, 64-bit core
  • Double precision 56 bit filter calculation
  • 3072 SIMD instructions per sample at 96 kHzASRCs from 1:8 up to 7.75:1 ratio and 139 dB DNR
  • 1 x USB serial data (connection PC / GUI)
  • 1 x remote connector (connection for RCD, RC-Mini, RTC-Hub)
  • 2 x bluetooth control port (connection MOS-BT3.0 (app control), RC-Can (CAN bus control)
  • 1 x remote out, 1 x remote In, auto-remote with highlevel connection
  • Connections with MOLEX® plug contacts
  • Very small size with low heat generation, best suited for installation behind cladding
  • 3 x 9 band parametric input EQ (de-equalizing)
  • 6 x input delay 0 - 3ms / 0.01ms (de-delay)
  • 10 x input level control digital (signal conditioning)
  • Flexible mixer for signal routing
  • (side separated, can sum and subtract, 10 inputs to 4 x 2 output groups)
  • 6 x 30 band or 4 x 30 band + 2 x 15 band group EQ
  • (parametric, relative phase remains stable)
  • 12 x 10 band output filters
  • Highpass / lowpass / highshelf / lowshelf / notch / allpass 1st + 2nd order / speaker-EQ)
  • 12 x speaker delay 0 - 12 ms, 0.01 ms
  • 12 x speaker phase switch
  • 8 x 60 W speaker output 3-Ohm stable (not bridgeable!)
  • 4 x 2 Vrms line outputs SN/R 112 dB
  • 1 x digital output optical (96 kHz / 24 Bit, fully masterable)
What's Included
  • MOSCONI PICO 8|12 DSP
FAQs
Q: How do I choose the right amplifier for my speakers or subwoofer?

A: Match the amplifier's RMS output per channel to the RMS handling of your speakers or subwoofer at the same impedance. The Specification tab lists the power figures. If in doubt, contact CEN with your setup and we will recommend a match.

Q: What wiring do I need to install this amplifier?

A: You will need an amplifier wiring kit sized to the amplifier's power draw, typically including power and earth cable, a fuse, RCA leads and a remote wire. CEN stocks complete wiring kits, and the amplifier's fuse rating is the guide to the cable gauge required.

Q: What class of amplifier is this and does it matter?

A: Class D amplifiers are compact and efficient, ideal for subwoofers and modern installs. Class AB designs are traditionally favoured for outright sound quality on mid and high frequencies. The class is listed in the Specification tab where provided.

Q: Will an amplifier work with my factory head unit?

A: Yes, in most cases. If your head unit has no RCA outputs you will need a line output converter to feed the amplifier a clean signal. CEN stocks line output converters and can advise the right one for your vehicle.

Q: Can CEN install this amplifier?

A: Yes. CEN offers professional amplifier installation from our Nottingham premises, including secure mounting, wiring and setup. Contact us to book.

Product information

About the brand

Mosconi

One of Mosconi's standout products is its line of DSPs, which enable precise tuning of audio systems to achieve optimal sound reproduction in car environments. These digital processors allow for advanced equalization, time alignment, and crossover settings, ensuring that every note and frequency is reproduced accurately according to the listener's preferences.

Mosconi Electronics continues to be a preferred choice among discerning car audio enthusiasts and professionals seeking top-tier sound performance and craftsmanship in their vehicles.

Shop Mosconi

Looking for Installation?

At CEN we take pride in being able to share the quality of our work as well as being able to show what incredible products we have installed week on week.

Get a quote

Recently Viewed

Jump back to the products you've been checking out

Reviews

No reviews yet — be the first to review this product.

Write a review