Helix M Four 4 Channel Amp Small Footprint Class D Amplifier up to 400w RMS
HELIX M FOUR 4 Channel Class D Amplifier HELIX M FOUR
If you like to rev up your front and rear speakers, the M FOUR will be exactly the right "tool" to do so. With generously 100 Watts RMS per channel into both 4 Ohms and 2 Ohms load this amp will heat up your voice coils in no time despite its super-compact dimensions. On the other hand the M FOUR stays totally cool thanks to the highly efficient Class D design topology. 3-channel or 2-channel configurations are possible as well, delivering up to 2 x 200 Watts RMS of clean and undistorted output power.
Needless to say that the M FOUR is equipped with a bunch of intelligent attributes like "start-stop capability" and our proprietary "ADEP" highlevel input so that it easily deals with all installation challenges of modern cars. Finally the extensive audio features will offer a sound quality at its best.
Features
- Small footprint Class D amplifier with high output power of 100 Watts RMS @ 4 and 2 Ohms load
- Start-Stop capability down to 6V supply voltage
- Smart highlevel input with ADEP circuit (Advanced Diagnostics Error Protection) and Auto Turn-On function
- Integrated, active crossover with highpass, lowpass and bandpass
- “Input mode” switch for flexible input signal routing
- SMD (Surface Mounted Device) manufacturing technology combines minimum space requirement with maximum reliability
- Exclusive, extremely compact and clean design with illuminated HELIX-logo and low heat dissipation thanks to extraordinary efficiency
Smart highlevel input
The latest generation of OE car radios incorporates sophisticated possibilities of diagnosing the connected speakers. If a common amplifier will be hooked up failure messages and loss of specific features (e.g. fader function) quite often appear - but not with the M FOUR.
The new ADEP circuit (Advanced Diagnostics Error Protection) avoids all these problems without loading the speaker outputs of the OE radio during high volumes unnecessarily.
Start-Stop capability
The switched power supply of the HELIX M FOUR assures operation even if the battery’s voltage drops down to 6 Volts during engine crank.
Specification
Part Number: M FOUR
- Output power RMS / max.
- - @ 4 Ohms 4 x 100 / 200 Watts
- - @ 2 Ohms 4 x 100 / 200 Watts
- - @ 1 Ohm -
- - bridged @ 4 Ohms 2 x 200 / 400 Watts
- - bridged @ 2 Ohms -
- Max. output power per channel* Up to 135 Watts RMS @ 4 / 2 Ohms
- Amplifier technology Class D
- Inputs 4 x RCA / Cinch
- 4 x Highlevel speaker input
- 1 x Remote In
- Input sensitivity RCA / Cinch 0.5 - 6 Volts
- Highlevel 1.3 - 13 Volts
- Input impedance RCA / Cinch 20 kOhms
- Input impedance highlevel 9 - 33 Ohms
- Outputs 4 x Speaker output
- Output voltage RCA / Cinch -
- Signal converter for digital input -
- Frequency response 10 Hz - 30,000 Hz
- Bass boost -
- Highpass 15 Hz - 4,000 Hz adjustable
- Lowpass 40 Hz - 4,000 Hz adjustable
- Bandpass 15 Hz - 4,000 Hz adjustable
- Subsonic -
- Phase -
- Slope high- / lowpass 12 dB/Oct.
- Slope subsonic / lowpass -
- Signal-to-noise ratio digital input -
- Signal-to-noise ratio analog input 98 dB (A-weighted)
- Distortion (THD) 0.05 %
- Damping factor 100
- Operating voltage 10.5 - 16 Volts (max. 5 sec. down to 6 Volts)
- Idle current 1,100 mA
- Fuse 2 x 30 A Maxi-fuse (APX)
- Additional features Active, adjustable crossover, input mode switch, Start-Stop capability, highlevel input with automatic turn on function and Advanced Diagnostics Error Protection (ADEP)
- Dimensions (H x W x D) 50 x 230 x 154 mm /
- 2.00 x 9.06 x 6.06”
* In typical multi-channel applications (2- / 3-way system + rear + subwoofer)
What's Included
2 Year Warranty
- Amplifier HELIX M FOUR
- Mounting material
- Instruction manual
About the brand
