TwK-88

System Tuning DSP controlled by TüN software, 8-ch. Analog & Digital Inputs / 8-ch. Analog Outputs

System Tuning DSP with 8-ch. Stereo RCA Inputs / 2 Digital (Optical and Coaxial) Inputs / 8-ch. Stereo RCA Outputs / 1 Digital Optical Output

The TwK™ 88 is a state-of-the-art digital signal processor engineered to deliver world-class system tuning capabilities in an easy-to-use format. Equipped with an advanced 24-bit DSP processor, the TwK™ 88 includes flexible input/output options, 80 total bands of equalization and powerful mixing tools. The included DRC-200 Digital Remote Controller offers dual level controls, toggles up to six presets, and has an LED indicator.

Control the TwK™ 88’s entire feature set by connecting it to your PC via USB, using the companion TüN™ Software interface.

• Flexible input design with 8 differential-balanced, line-level analog inputs (RCA), accepting line-level signals up to 7.1V (RMS)
• Separate optical (Toslink) and coaxial digital inputs for connection to digital S/PDIF sources.
• Flexible input mixer allows input channels to be combined with full control over each input’s level and polarity.
• 8 banks of 10-band graphic or parametric equalizers with configurable EQ assignment
• Powerful crossover section with fully variable, high-pass and low-pass filters, crossover slopes are selectable from 6 dB/octave to 48 dB/octave (in 6 dB/octave increments)
• Configurable polarity and delay settings, with separate entries for speaker distance plus offset control; fully linkable with other channels, in any combination, for adjustment
• Precise output level controls, adjustable in 0.5 or 0.1 dB increments, fully linkable with other channels, in any combination
• 8 analog, line-level RCA output jacks (4V RMS)
• Optical (Toslink) output jack provides a pass-through digital audio (S/PDIF) signal from any pair of input channels, with no signal processing applied.
• Remote turn-on output (+12VDC) for activating aftermarket audio equipment.
• JLid™ Port allows connection of the included DRC-200 Digital Remote Controller to add dual configurable level controls, preset selection and LED status reporting from the driver's seat.

• Power Supply Type    Regulated DC-DC SMPS
• Input Operating Voltage    10 - 16 VDC
• Standby Current Draw    <1.5 mA
• Operating Current Draw    0.7 A
• Recommended Fuse Value    1 A
• Input Channels    Eight
• Input Type    Line-level, Differential-Balanced
• Input Voltage Range    250 mV - 7.1 V RMS
• Minimum Input Voltage    10 mV RMS
• Input Level Setting    Eleven discrete selections from 250 mV - 7.1V RMS
• Output Channels    Eight
• Analog Output    Unbalanced, stereo RCA jacks
• Digital Output    Optical (Toslink) output (S/PDIF)
• Output Impedance    450 Ω
• Latency    Analog - Analog: 5.425 mS
• Analog - Optical: 5.470 mS
• Optical - Optical: 4.860 mS
• Optical - Analog: 4.805 mS
• S/N Ratio    98 dB (A-Weighted, referred to 4V RMS Output)
• THD+N @ Rated Output    0.02% (20 Hz - 20 kHz)
• Audio Resolution    24 bit / 48 kHz
• Number of EQ Bands    10 x 8 Channels
• Remote Level Control    Included (DRC-200)
• Remote Level Functions    Master Volume Control + Trim; Master Volume Control + Fader; Zone Control, LED Status Reporting

• Processor
• 5-Pin Euroblock (Phoenix) connector
• 15' USB cable (Type-A on one end
• Type-B on other end
• 2.0)
• 18' Control cable w/ RJ-45 connectors on both ends
• DRC-200 Level Control Knob w/ 46" attached cord terminating in a female RJ-45 socket and attached status LED w/ 38" cord
• LED mounting collar
• Two locking nuts
• Two flat washers
• Owner's manual